Www.franklinfueling.com 0000200 REV C E - m a i l: t e c h @ f r a n k l i n f u e l i n g. C o m F A X 1 - 2 0 7 - 2 8 2 - 9 0 0 2 T E L 1 - 8 0 0 - 9 8 4 - 6 2 6 6 P A G E 1 o f 4 s a l e s @ i n t e l c o n. C o m F A X 1 - 2 0 7 - 2 8 3 - 0 1 5 8 T E L 1 - 8 0 0 - 8 7 2 - 3 4 5 5 REPLACEMENT PART INSTRUCTIONS Main System Board Installation for Tank Sentinel, AutoStik, BulkStik ATGs TS-1001/N-N U10 VER No. DATE Diagram: A Tank Sentinel (Except TS-2001), AutoStik Jr, BulkStik, AutoStik II (1-4ch) 050-0200 1001/2001 (U10) REV. / VER N.NN Diagram: B TS-2001, AutoStik II (8 Ch).
E Issue Date: July 27, 2004 Revision Date: April 6, 2010 Franklin Fueling Systems (originally listed as EBW, Inc.) AutoStik II, AutoStik Jr. (INCON, EBW LL2 Magnetostrictive Probe) AUTOMATIC TANK GAUGING METHOD As of April 1, 2009, Franklin Fueling systems no longer manufactures this method. Certification Applies only to AutoStik II and AutoStik Jr. Models sold March 1, 2004 to April 1, 2009.
Leak rate of 0.2 gph with PD = 95.7% and PFA = 4.3%. Leak Threshold 0.1 gph. A tank system should not be declared tight if the test result indicates a loss or gain that equals or exceeds this threshold. Applicability Gasoline, diesel, aviation fuel, fuel oil #4. Tank Capacity Maximum of 30,000 gallons. Tanks less than 95% full may be tested.
Minimum product level required based on tank diameter as follows: 48' dia/min 12'; 64' dia/min 14'; 72'dia/min 15'; 96' dia/min 17.5'; 126'dia/min 21.5'. For other diameters, see evaluation report. Waiting Time Minimum of 4 hours 9 minute between delivery and testing. Minimum of 2 hours between dispensing and testing. There must be no delivery during waiting time.
Ebw Auto Stik Jr Manual
Test Period The length of the test is determined automatically based on quality of test data. Average data collection time during the evaluation was 6 hours, 51 minutes. Test data is acquired and recorded by system's computer. Leak rate is calculated from data determined to be valid by statistical analysis.
There must be no dispensing or delivery during the test. Temperature Probe contains 5 thermistors to monitor product temperature. At least one thermistor must be submerged in product during testing. Water Sensor Must be used to detect water ingress. Minimum detectable water level in the tank is 0.208 inches. Minimum detectable water level change is 0.011 inch.
Ebw Auto Stik Jr
Calibration Thermistors and probe must be checked and, if necessary, calibrated in accordance with manufacturer's instructions. Comments Not evaluated using manifolded tank systems. Therefore, this certification is only applicable when there is a probe used in each tank and the siphon is broken during testing. This equipment was not evaluated using manifolded tanks. Tests only the portion of the tank containing product.
As product level is lowered, the leak rate in a leaking tank decreases (due to lower head pressure). Consistent testing at low levels could allow a leak to remain undetected. EPA leak detection regulations require testing of the portion of the tank system which routinely contains product. Can support up to 4 tanks.
AutoStik II can support up to 8 tanks. Franklin Fueling Systems Evaluator: Ken Wilcox Associates 3760 Marsh Road Tel: (816) 443-2494 Madison, WI 53718 Dates of Evaluation: 05/14/98, 08/21/02 Tel: (800) 225-9787 E-mail: [email protected] URL: www.franklinfueling.com Appearance on this list is not to be construed as an endorsement by any regulatory agency nor is it any guarantee of the performance of the method or equipment.
Auto Stik Jr Manual
Equipment should be installed and operated in accordance with all applicable laws and regulations. For full details, please refer to our expanded ' page. Eliminator 2000w inverter manual.